8130 XR-5® Geomembranes
High Performance 8130 XR-5 Reinforced Geomembrane
|
|
|
|
|---|---|---|
| Base Fabric Type |
Polyester |
|
| Base Fabric Weight (nominal) ASTM D751 |
6.5 oz/yd2 |
220 g/m2 |
| Thickness ASTM D751 |
30 mils nominal | 0.76 mm min |
| Weight ASTM D751 |
30.0 ± 2 oz/yd2 | 1017 ± 70 g/m2 |
| Tear Strength ASTM D4533 Trapezoid Tear |
40/55 lbs min | 175/245 N min |
| Breaking Yield Strength ASTM D751, Grab Tensile |
550/550 lb min | 2448/2448 N min |
| Low Temperature Resistance ASTM D 2136, 4 hr - 1/8" mandrel |
Pass @ -30 º F | Pass @ -34 º C |
| Dimensional Stability ASTM D1204, 212° F/100° C - 1 hr |
each direction |
|
| Adhesion - Heat Sealed Seam ASTM D751, Dielectric Weld |
40 lb/2 in min | 17.5 daN/5 cm min |
| Dead Load - Seam Strength ASTM D751, 4-hour test |
2 in seam, 1 in strip Pass 240 lb/in @ 70º F Pass 120lb/in @ 160º F |
5 cm seam, 2.5 cm strip Pass 1068 N/2.54 cm @ 21º C Pass 534 N/2.54 cm @ 70º C |
| Bursting Strength ASTM D751, Ball Tip |
750 lb min | 3330 N min |
| Hydrostatic Resistance ASTM D751, Procedure A |
800 psi min | 5.51 MPa min |
| Blocking Resistance ASTM D751 (180º F/82º C) |
|
|
| Adhesion - Ply ASTM D413, Type A |
15 lb/in min or Film Tearing Bond |
13 daN/5 cm min or Film Tearing Bond |
| Bonded Seam Strength ASTM D751, Grab Test Method, Procedure A |
550 lb min | 2450 N min |
| Abrasion Resistance ASTM D3389, H-18 Wheel, 1 kg Load |
50 mg/100 cycles max weight loss |
|
| Weathering Resistance ASTM G153 (Carbon Arc) |
or stiffening or cracking of coating |
|
| Water Absorption ASTM D471, Section 12, 7 days |
0.14 kg/m2 max @ 212º F/100º C |
|
| Wicking ASTM D751 |
1/8 in max | 0.3 cm max |
| Puncture Resistance ASTM D4833 |
275 lb min | 1200 N min |
| Coefficient of Thermal Expansion/Contraction ASTM D696 |
8 x 10-6 in/in/ºF max | 1.4 x 10-5 cm/cm/ºC max |
| Environmental/Chemical Resistant Properties | See Chemical Resistance Table | |
| Puncture Resistance FED-STD 101C Method 2031 |
350 lb (approx) | 1550 N (approx) |
Seaming: Thermal welding methodes are recommended. No glues or solvents are suggested.
We believe this information is the best currently available on the subject. We offer it as a suggestion in any appropriate experimentation you may care to undertake. It is subject to revision as additional knowledge and experience are gained. We make no guarantee of results and assume no obligation or liability whatsoever in connection with this information. In case of conflict between standard and metric specifications, standard shall apply.
